Видео

what temp and airflow when removing the chip?

Thanks for the video, I know it takes time and effort and the meaning is in all good intentions , but I do question your soldering iron, I will say that is got to be the worst iron I have ever seen. I'm amazed it could even heat transfer and all the gunk on it full of contamination, I would be worried that your solder joints are going to fail. I clean my irons every three or four spots . But what do I know ? I just restore vintage amplifiers and Ham radios as a part time business.

Do you sell these?

Song???

Way too fast, to learn something from this. Also hardly any explanations...

Didn't tell you how to do anything

Well, i am with aaronspencer1880 in that points, that you need to take ensure that the pad place of the removed chip should be clean from flux and solder. Flux is your fried - i aggree, but use them as less as you can. The chip swim into the flux and this will be bad in the future because it's nasty and corrosive. Cleaning and preparing the pads is the most important work that have to be done to get a solid and reliable solution.

02:30--так все дорожки перерезать можно, накрыв пилоткой всю работу. Вот придумал-то, скальпелем наносить флюс...

Thanks! Fast and precise explanation = great!

When I use rtclib, program not upload. Error 1 is come. Why sir ?

ATtiny85

but, bear in mind that, the flux you are using should be of good quality.

I need help

Hi , I have to put the code for the ds3231 every time I build thumthing or only once ?

How to hack any IR LED Solar PIR Motion Sensor Lamp Outdoor Garden Security Wall Street Light

Have you ever upgraded GPU VRAM like this?

DK Technology Sewing Machine All Kinds of Garments Accessories &Circuit Service Solution Dhaka Gazipur Bangladesh

Wow!

What make of iron do you use ?

Why only 4.7k

Step one, clean that corrosion off the connector. Haha. Thank you for the video.

One of the best tutorials in RUclips to learn solder 256 pin SMD! Please keep up your good work! I am going to try this out to swap my BIOS SMD to new PCB, wish me luck 🤞

Can i use arduino uno r3 intead of arduino nano?

Awesome Nice work

😅

How do you then control a relay output?

How can I get the flux dispenser pen and the tools you used to check the brake.

WHAT A FREAK THIS GUY GIVES YOU NO CODE

You really need to fix your audio, I can't hear a thing and I've got it on 100%

so easyyy

Good job .

Can you set alarms to 10 times every day?

How do I reset the it remote with Arduino

Cảm ơn đã chia sẻ, nó rất hữu ích cho tôi.

Dear friend, your explanation is very valuable. I wanna know the type and watts of your soldering iron.

Your circuit has no battery protection circuit. Lithium batteries are dangerous when not properly used. Your circuit could very easily over discharge your battery making it a fire hazard

If I have a 100watt 12 volt led chip, can I just run a 12volt battery directly to it?

Yeah but what can i do if i dont have the original remote anymore

can you make same with 8 bay(slot) aa battery holders?

Dude! That’s amazing!! Thanks for the tutorial!

All fake like his links to the products being non existent.

hihi

Thank you so much.

Nice useful tutorial 👍👌👌

how can i delete the content of the oled?

everything works fine, but when I disconnect the arduino from the PC, wait a few minutes, connect it again, Time starts from the moment where I cut off the power. Where is the fault hardware or software?

Good Video! Your live demonstration is encouraging to those starting out. Indeed " PRACTICE " and " PATIENCE " are Key to success.!

your voice so low. i cant hear you.

Where are you living that your room is 37 degrees cesius? How precise is that sensor?